Hpe Smart Array S100i Sr Gen10 Driver Windows Server 2022 Fixed • Instant Download

Here is comprehensive content regarding the HPE Smart Array S100i SR Gen10 driver for Windows Server 2022.

This content is structured to be useful for IT administrators, system builders, and users setting up HPE ProLiant Gen10 servers.

Method 3: Using HPE Image Assistant (Smart Update Manager)

For automated driver deployment across multiple servers:

Install HPE Image Assistant (formerly SUM) on Windows Server 2022.
Run the tool and baseline against your server.
Select the S100i driver component from the repository.
Apply the update and reboot.

Verifying Successful Installation

After loading the driver, confirm proper operation:

In Device Manager:
Expand "Storage Controllers" → "HPE Smart Array S100i SR Gen10" with no yellow exclamation mark.
In Disk Management:
Your RAID 1, 5, or 10 volume appears with correct capacity.
In HPE SSA (Smart Storage Administrator):
Install HPE SSA for Windows to view physical disks, RAID level, and health status.

Command-line check:

Get-PnpDevice -FriendlyName "*S100i*"

Output should show Status = OK.

HPE Smart Array S100i SR Gen10 — Windows Server 2022 write-up

Summary

The HPE Smart Array S100i SR Gen10 is an integrated software RAID controller (driver-based) used on HPE ProLiant Gen10 servers to provide SATA/SAS logical volume management (often for boot and local storage).
On Gen10 platforms the S100i is usually a “software RAID” (SATA controller with HPE driver) rather than a full hardware RAID offload card.

Compatibility with Windows Server 2022

Windows Server 2022 compatibility depends on HPE-provided drivers and the server model/firmware level.
For best results, use the HPE validated driver package specifically listed for your ProLiant Gen10 model and Windows Server 2022. HPE sometimes bundles drivers in the HPE Smart Storage Administrator (HPE SSA) and server OS driver packs.
If HPE has not published an explicit WS2022 driver for the S100i for your server model, the latest Windows Server 2019/2016 driver may work but is not guaranteed or supported.

Recommended approach (prescriptive)

Identify exact server model and current firmware/BIOS/iLO version.
From HPE’s Support site, download:
- The S100i driver package labeled for your server model and Windows Server 2022 (or the latest available OS driver pack).
- HPE Smart Storage Administrator (SSA) and any storage controller firmware updates for Gen10.
Apply server firmware and BIOS/iLO updates before installing the OS.
During Windows Server 2022 installation:
- If the installer does not see the OS/boot disks, load the S100i driver from a USB drive when prompted (“Load driver”).
After Windows is installed, install the HPE driver package and HPE SSA to ensure proper management and monitoring of logical drives and health reporting.
Test RAID creation, rebuild, and recovery procedures in your environment before production use.

Driver and firmware notes

Use vendor-supplied drivers (HPE) rather than generic Microsoft drivers for full functionality and support.
Firmware and driver versions must be compatible; updating drivers without corresponding firmware can cause issues.
HPE’s integrated controllers like S100i may have reduced feature sets compared with dedicated Smart Array hardware (e.g., battery-backed cache, advanced caching features).

Troubleshooting tips

If disks don’t appear in Windows setup: confirm controller mode (RAID vs AHCI) in BIOS and load the correct driver.
Check Device Manager for unknown storage controllers—use “Update driver” pointing to the extracted HPE driver folder.
Use HPE SSA to view logical drive state and for rebuilding or migration tasks.
Review HPE server logs (iLO) and Windows Event Viewer for storage/driver-related errors.

Support and lifecycle

Check HPE’s lifecycle documentation for Gen10 driver support timelines. Hardware may have limited or phased support for newer OS releases; always confirm support statements for your exact server SKU.

Quick checklist

Server model + firmware updated
Download HPE S100i driver package for WS2022 (or latest validated)
Install firmware/SSA before/after OS install as recommended
Load driver during Windows setup if required
Validate RAID behavior and monitoring after install

If you want, I can provide step-by-step commands for loading the driver during Windows Server 2022 setup or locate the specific HPE driver page for a particular ProLiant model (tell me the server model).

Conclusion

Successfully installing the HPE Smart Array S100i SR Gen10 driver for Windows Server 2022 is a mandatory step for any HPE ProLiant Gen10 administrator deploying Microsoft’s latest server OS. Without this signed HPE driver, your disks remain invisible, and the server cannot proceed past the storage selection screen.

Critical takeaways:

Always download the "HPE Dynamic Smart Array B140i/S100i Driver" package from the official HPE support portal.
Extract the driver before starting Windows Server 2022 setup.
Use the Load Driver method during OS installation for the smoothest experience.
After installation, verify the driver in Device Manager and consider updating your BIOS and HPE SSA tools.

When in doubt, leverage HPE’s Service Pack for ProLiant (SPP) or HPE Image Assistant to automatically deploy the correct driver package. With the S100i driver properly loaded, Windows Server 2022 will deliver stable, reliable storage performance for your entry-level Gen10 server.

Last updated: November 2025
Driver version used in examples – 6.3.0.57. Always check for newer releases on HPE.com.

Need further help? Visit the HPE Community forums or open a support case with HPE Pointnext.

Here’s a sample review for the HPE Smart Array S100i SR Gen10 driver on Windows Server 2022, written from the perspective of an IT administrator:

Title: Works after some effort – not plug-and-play
Rating: ⭐⭐⭐☆☆ (3/5)

Review:
I installed the HPE Smart Array S100i SR Gen10 software RAID controller on a ProLiant DL380 Gen10 running Windows Server 2022. The driver isn’t included in the base OS, so you’ll need to download it manually from HPE’s support site.

Pros:

Once installed, disk management and SMART monitoring work fine.
No stability issues after successful setup.
Works well for basic RAID 0/1/10 setups.

Cons:

Installation requires booting into OS first or injecting drivers via DISM – annoying for fresh OS installs.
HPE’s website can be confusing to locate the exact correct driver version.
No native GUI management tool (you rely on diskpart or HPE SSA CLI).
Performance is mediocre compared to hardware RAID.

Tip: Use the latest driver version (e.g., 8.7.0.118 or newer). Install via pnputil or HPE’s PowerShell script. Don’t forget to enable S100i in UEFI BIOS first.

Bottom line: Good for basic internal storage, but avoid for production workloads needing high IOPS or reliability. Recommended only if you’re stuck with the embedded controller.

HPE Smart Array S100i SR Gen10 driver is fully supported on Windows Server 2022 hpe smart array s100i sr gen10 driver windows server 2022

. Since this is a software-based RAID solution, the driver is not included in standard Windows installation media; you must manually provide it for the installer to recognize your logical volumes. Hewlett Packard Enterprise Essential Driver Information

To ensure stability and performance, use the dedicated driver version released specifically for the 2022 OS: 1010.14.0.0(C) Release Date: September 28, 2022 Download Source: HPE Support Center - S100i Driver for Windows Server 2022 Installation Best Practices Preparation: Download the driver package and extract the contents to a before starting your OS installation.

During the "Where do you want to install Windows?" step, click Load Driver and browse to the extracted folder on your USB. Automation Option: HPE Intelligent Provisioning

to automate the driver injection process during the OS install. Requirement Check: requires UEFI Boot Mode

; it is not supported if the server is configured for Legacy BIOS. Hewlett Packard Enterprise Quick Comparison: vs. SR100i

Verify your server model to ensure you are using the correct software RAID driver: S100i SR Gen10

Designed for standard ProLiant Gen10 servers (e.g., DL360/DL380 Gen10). SR100i Gen10 Plus Specifically for Gen10 Plus platforms. If you have a "Plus" model, use Driver Version 1010.124.100.1005 Hewlett Packard Enterprise UEFI configuration steps

to enable Software RAID mode before starting your installation?

How to Download the Driver

There are two primary methods to obtain the correct driver for Windows Server 2022 (x64).

🔧 Management Tools

Use HPE S100i BIOS Configuration Utility (F10 during boot) or HPE Smart Storage Administrator (SSA) within Windows Server 2022 after driver installation.